Comparative analysis of turbulent heat transfer in square duct with heated foil boundary conditions
This project investigates turbulent heat transfer in a square duct configuration where a finite section of a single duct boundary is heated with an infinitely thin foil. The research compares Direct Numerical Simulation (DNS) and Large Eddy Simulation (LES) approaches to understand their relative accuracy and computational efficiency for nuclear thermal hydraulics applications.
Motivation and Background
Temperature fluctuations at heated surfaces in turbulent flows matter for nuclear reactor safety analysis, for example through thermal fatigue. Understanding these phenomena requires accurate prediction of near-wall thermal boundary layer behavior, which presents significant challenges for computational methods. This work addresses the fundamental question of when LES can reliably replace DNS for thermal hydraulics calculations.
Research Objectives
Method Validation: Compare DNS and LES-WALE model predictions for thermal boundary layer behavior
Accuracy Assessment: Quantify differences in temperature statistics and fluctuation predictions
Computational Efficiency: Evaluate the cost-benefit trade-offs between high-fidelity DNS and practical LES
Design Support: Provide guidance for experimental design in thermal hydraulics research
Key Results
Temperature Prediction Differences
The standard LES-WALE model predicts about 20% higher foil temperatures and temperature fluctuations than DNS.
Near-Wall Model Behavior
A detailed analysis of the LES-WALE model’s near-wall behavior explains the discrepancy. LES-WALE is highly accurate only on finely resolved meshes, and the cost of that refinement is hard to justify when DNS is an option.
Methodology
Numerical Setup
Code: OpenFOAM with second-order accurate schemes
Approach: Passive scalar approximation for thermal transport
Boundary Conditions: Constant heat flux at heated foil section
Reynolds Number: 10,000 (fully developed turbulent flow)
Computational geometry showing square duct configuration with heated foil boundary section for DNS vs LES comparison
Comparative Framework
DNS: High-resolution reference solution capturing all turbulent scales
LES: Wall-Adapting Local Eddy-viscosity (WALE) subgrid-scale model
Mesh Sensitivity: Systematic grid refinement studies for both methods
Applications and Impact
This research supports:
Nuclear reactor thermal analysis by providing method accuracy guidelines
Experimental design for heated foil thermometry studies
CFD code validation for nuclear thermal hydraulics applications
Computational resource planning for industrial simulations
Experimental Connection
The simulations supported the design of the heated-foil experiment in the THELMA laboratory at Jožef Stefan Institute. LES of the planned setup set the foil heating power, and the analysis of coherent thermal structures determined the spatial resolution and frame rate the high-speed thermal camera needs.
Turbulent heat transfer in a square duct, where a finite section of a single duct boundary is heated with an infinitely thin foil, was analyzed with LES and DNS approaches. Both computations were performed with OpenFOAM code with passive scalar approximation, using second order accurate schemes. Results are obtained for the key velocity and temperature statistics in the duct, with an emphasis on the temperature profiles and temperature fluctuations at the foil boundary, which appear due to the imposed constant heat flux boundary condition at the foil. Comparison of DNS and standard LES-WALE model show 20% higher foil temperatures and temperature fluctuations in LES results. These differences are explained with detailed analysis of the LES-WALE model near-wall behavior. It has been demonstrated that LES-WALE yields highly accurate results only when employed with a finely resolved mesh. However, the computational costs associated with such refinement may not be necessarily justified especially with respect to DNS.
2023
Thermal streak spacing in fully developed duct flow with different Reynolds and Prandtl numbers
Mohit Pramod Sharma, Iztok Tiselj, Jan Kren, and 2 more authors
At Reactor Engineering Division of Jozˇef Stefan Institute a new experiment is being built in the THELMA laboratory to study temperature fluctuations at the wall cooled by adjacent turbulent flow. As the experiments are limited especially in resolution and also in the available insight into the flow and thermal field, Computational Fluid Dynamics (CFD) studies are widely used as a design support to fluid dynamics experiments.
Simulacije turbulentnega prenosa toplote ob greti foliji z metodo velikih vrtincev
Jan Kren
Univerza v Ljubljani, Fakulteta za matematiko in fiziko, 2020
Na Odseku za reaktorsko tehniko Inštituta Jožef Stefan se postavlja nov eksperiment v Laboratoriju za termohidravliko večfaznih tokov (THELMA). Namen eksperimenta je študija temperaturnih fluktuacij na greti kovinski foliji, ki je hlajena s turbulentnim tokom. Načrtovanje eksperimenta temelji na numeričnih simulacijah, v katerih smo analizirali vpliv različnih aproksimacij na temperaturne fluktuacije na greti foliji. To delo opisuje rezultate simulacij. Tok in prenos toplote v novem eksperimentu smo napovedali s simulacijami z metodo velikih vrtincev (ang. Large Eddy Simulation) s pomočjo računalniškega programa OpenFOAM. Prevajanja toplote v foliji nismo modelirali. Folijo smo opisali z idealiziranim robnim pogojem konstantnega toplotnega toka. Simulacije so predpostavljale nestisljiv, polno razvit turbulentni tok Newtonske tekočine z Reynoldsovim številom 10000. V prvih simulacijah je bila dodana temperatura kot pasivni skalar, torej brez povratne zanke na enačbo za ohranitev gibalne količine. Drugi del simulacij pa je upošteval spreminjanje viskoznosti vode s temperaturo ter vzgonske sile. Določili smo ustrezno toplotno moč folije v eksperimentu ter moč, pri kateri je mogoče zanemariti vpliv temperature na materialne lastnosti vode. Posebej nas je zanimala porazdelitev temperature na vroči foliji v turbulentnem režimu. Z analizo koherentnih termičnih struktur v simulacijah smo uspeli določiti potrebno resolucijo in frekvenco visokohitrostne termične kamere pri danemu Reynoldsovemu in Prandtlovemu številu. V zaključku je predstavljena kratka primerjava naših simulacij s preliminarnimi meritvami temperaturnih fluktuacij na greti foliji.